09/17/2024


In this study, we examine the effect of integrating different carbon nanostructures (carbon nanotubes, CNTs, graphene nanoplatelets, GNPs) into Ni- and Ni-W-based bi-functional catalysts for hydrocracking of heptane performed at 400 °C. The effect of varying the SiO2/Al2O3 ratio of the zeolite Y support (between 5 and 30) on the heptane conversion is also studied. The results show that the activity, in terms of heptane conversion, followed the order CNT/Ni-ZY5 (92%) > GNP/Ni-ZY5 (89%) > CNT/Ni-W-ZY30 (86%) > GNP/Ni-W-ZY30 (85%) > CNT/Ni-ZY30 (84%) > GNP/Ni-ZY30 (83%). Thus, the CNT-based catalysts exhibited slightly higher heptane conversion as compared to the GNP-based ones. Furthermore, bimetallic (Ni-W) catalysts possessed higher BET surface areas (725 m2/g for CNT/Ni-W-ZY30 and 612 m2/g for CNT/Ni-ZY30) and exhibited enhanced hydrocracking activity as compared to the monometallic (Ni) catalyst with the same zeolite support and type of carbon structure. It was also shown that CNT-based catalysts possessed higher regeneration capability than their GNP-based counterparts due to the slightly higher thermal stability of the CVD-grown CNTs.Herein, step-scheme (S-scheme) CuBi2O4/CuO (CBO/CuO) composite films were successfully synthesized on glass substrates by the ultra-fast spraying-calcination method. The photocatalytic activities of the obtained materials for CO2 reduction in the presence of H2O vapor were evaluated under visible light irradiation (λ > 400 nm). Benefiting from the construction of S-scheme heterojunction, the CO, CH4 and O2 yields of the optimal CBO/CuO composite reached 1599.1, 5.1 and 682.2 μmol/m2 after irradiation for 9 h, and the selectivity of the CO product was notably enhanced from below 18.5% to above 98.5% compared with those of the bare samples. In the sixth cycling experiment, the yields of main products decreased by less than 15%, and a high CO selectivity was still kept. The enhanced photocatalytic performance of CO2 reduction was attributed to the efficient separation of photogenerated charge carriers. Based on the photocatalytic activity, band structure and in situ-XPS results, the S-scheme charge transfer mechanism was conformed. The study provides an insight into the design of S-scheme photocatalysts for selective CO2 conversion.To systematically investigate the diffusion behavior of Fe/Cu bimetallic materials and the influence of the Ni element on the diffusion and mechanical properties of the Fe/Cu bimetallic interface, the diffusion distance, diffusion coefficient, and strain-stress process based on molecular dynamics (MD) calculations and experimental testing were analyzed. All simulation results indicated that the liquid Cu matrix had a higher diffusion coefficient but hardly diffused into the Fe matrix, and the solid Fe matrix had a smaller diffusion coefficient but diffused deep into the Cu matrix at the same temperature. Compared with the initial state, the addition of nickel atoms to the Cu matrix favored the improvement of the diffusion coefficient and the diffusion distance of Fe/Cu bimetallic materials. Moreover, we found that the diffusion distance and the yield strength simultaneously increased and then decreased with the increase in Ni atoms, which is in agreement with the experimental test results. These improvements in the diffusion and mechanical properties were attributed to the enrichment of Ni atoms at the interface, but excessive Ni content resulted in deteriorated properties. Finally, our research described the enhancement mechanism of the addition of nickel atoms to the Fe/Cu bimetallic diffusion system. An analysis of the contributions of the diffusion distance, the diffusion coefficient, and the yield strength revealed that the diffusion properties of nickel atoms play an important role in Fe/Cu bimetallic materials.Undoped and Zn-doped ITO (ITOZn) multifunctional thin films were successfully synthesized using the sol-gel and dipping method on three different types of substrates (glass, SiO2/glass, and Si). https://www.selleckchem.com/products/genipin.html The effect of Zn doping on the optoelectronic, microstructural, and gas-sensing properties of the films was investigated using X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), spectroscopic ellipsometry (SE), Raman spectroscopy, Hall effect measurements (HE), and gas testing. The results showed that the optical constants, the transmission, and the carrier numbers were correlated with the substrate type and with the microstructure and the thickness of the films. The Raman study showed the formation of ITO films and the incorporation of Zn in the doped film (ITOZn), which was confirmed by EDX analysis. The potential use of the multifunctional sol-gel ITO and ITOZn thin films was proven for TCO applications or gas-sensing experiments toward CO2. The Nyquist plots and equivalent circuit for fitting the experimental data were provided. The best electrical response of the sensor in CO2 atmosphere was found at 150 °C, with activation energy of around 0.31 eV.Exploiting multifunctional thin film transistors (TFTs) by low-temperature manufacturing strategy is a crucial step toward flexible electronics. Herein, a multifunctional indium-tungsten-oxide (IWO)-based TFT, gated by solid-state chitosan electrolyte membrane, is fabricated on paper substrate at room temperature. The chitosan exhibits a high specific electric-double-layer capacitance of 2.0 µF cm-2 due to the existence of mobile protons. The IWO-based TFT possesses excellent electrical properties, including a low threshold voltage of 0.2 V, larger current switching ratio of 1.3 × 106, high field effect mobility of 15.0 cm2 V-1s-1, and small subthreshold swing of 117 mV/decade, respectively. Multifunctional operations including inverter, Schmitt triggers, and NAND gate are successfully demonstrated. As an example of information processing, the essential signal transmission functions of biological synapses also be emulated in the fabricated IWO-based TFTs. The experimental results indicate that such flexible IWO-based TFTs on low-cost and biodegradable paper provide the new-concept building blocks for flexible electronics.A systematic study of the most significant parameters of the ion-assisted deposited silicon dioxide films is carried out using the classical molecular dynamics method. The energy of the deposited silicon and oxygen atoms corresponds to the thermal evaporation of the target; the energy of the assisting oxygen ions is 100 eV. It is found that an increase in the flow of assisting ions to approximately 10% of the flow of deposited atoms leads to an increase in density and refractive index by 0.5 g/cm3 and 0.1, respectively. A further increase in the flux of assisting ions slightly affects the film density and density profile. The concentration of point defects, which affect the optical properties of the films, and stressed structural rings with two or three silicon atoms noticeably decrease with an increase in the flux of assisting ions. The film growth rate somewhat decreases with an increase in the assisting ions flux. The dependence of the surface roughness on the assisting ions flux is investigated. The anisotropy of the deposited films, due to the difference in the directions of motion of the deposited atoms and assisting ions, is estimated using the effective medium approach.Recycling waste biomass into valuable products (e.g., nanomaterials) is of considerable theoretical and practical significance to achieve future sustainable development. Here, we propose a one-pot hydrothermal synthesis route to convert waste tobacco stems into biomass-based N, S-codoped carbon dots (C-dots) with the assistance of carbon black. Unlike most of the previously reported luminescent C-dots, these biomass-based C-dots showed a satisfactory stability, as well as an excitation-independent fluorescence emission at ~520 nm. Furthermore, they demonstrated a pH-dependent fluorescence emission ability, offering a scaffold to design pH-responsive assays. Moreover, these as-synthesized biomass-based C-dots exhibited a fluorescence response ability toward tetracycline antibiotics (TCs, e.g., TC, CTC, and OTC) through the inner filter effect (IFE), thereby allowing for the establishment a smart analytical platform to sensitively and selectively monitor residual TCs in real environmental water samples. In this study, we explored the conversion of waste tobacco stems into sustainable biomass-based C-dots to develop simple, efficient, label-free, reliable, low-cost, and eco-friendly analytical platforms for environmental pollution traceability analysis, which might provide a novel insight to resolve the ecological and environmental issues derived from waste tobacco stems.The anisotropy engineering of nanoporous zinc oxide (ZnO) frameworks has been performed by lattice dynamics simulation. A series of zinc oxide (ZnO) nanoporous framework structures was designed by creating nanopores with different sizes and shapes. We examined the size effects of varying several features of the nanoporous framework (namely, the removal of layers of atoms, surface-area-to-volume ratio, coordination number, porosity, and density) on its mechanical properties (including bulk modulus, Young's modulus, elastic constant, and Poisson ratio) with both lattice dynamics simulations. We also found that the anisotropy of nanoporous framework can be drastically tuned by changing the shape of nanopores. The maximum anisotropy (defined by Ymax/Ymin) of the Young's modulus value increases from 1.2 for bulk ZnO to 2.5 for hexagon-prism-shaped ZnO nanoporous framework structures, with a density of 2.72 g/cm3, and, even more remarkably, to 89.8 for a diamond-prism-shape at a density of 1.72 g/cm3. Our findings suggest a new route for desirable anisotropy and mechanical property engineering with nanoporous frameworks by editing the shapes of the nanopores for the desired anisotropy.The effects of 44 types of elements on the stabilities of I1-constitute multi-type long-period stacking-ordered (LPSO) structures in Mg alloys, such as 4H, 6H, 8H, 9R, 12H, 15R, and 16H phases, are systematically investigated by first-principle high-performance calculations. The intrinsic stacking-fault energies (ISFEs) and their increments are calculated along with the formation enthalpies of solute atoms, and interaction energies between solute atoms and LPSO structures. The results suggest that the 15R phase is the easiest to form and stabilize among these LPSO structures, and 44 types of solute atoms have different segregation characteristics in these LPSO structures. A high temperature inhibits structural stabilizations of the LPSO phases, and these alloying elements, such as elements (Sb, Te, and Cs) for 4H; elements (S, Fe, Sb, and Te) for 6H, 8H, 9R, 15R, and 16H; and elements (S, Sb, and Te) for 12H, can effectively promote the stability of LPSO structures at high temperatures. S and Fe atoms are the most likely to promote the stabilities of the 16H structure with regard to other LPSO phases, but the Fe atom tends to inhibit the stabilities of 4H and 12H structures. This work can offer valuable references to further study and develop high-performance Mg alloys with multi-type LPSO structures.